亲宝软件园·资讯

展开

【原理】从零编写ILI9341驱动全过程（基于Arduino）

lyj00912 人气:0

最近在淘宝入手了一块ILI9341彩色屏幕，支持320x240分辨率。之前一直很好奇这类单片机驱动的彩色屏幕的原理，就打算自己写一个驱动，从电流层面操控ILI9341屏幕。话不多说，我们开始吧(￣▽￣)~*

1.ILI9341芯片和ILI9341驱动板

首先这里要明确两个概念，ILI9341芯片和ILI9341驱动板。

ILI9341芯片是ilitek发布的液晶驱动芯片，是这个样子的：

而淘宝上的ILI9341驱动板是把ILI9341芯片、屏幕和针脚焊接在一起的电路板，它可能是这个样子的：

 

也可能是这个样子的：

 

 还可能是这个样子的：

 

没错，不同的厂家可以制造不同形状，不同接口的ILI9341驱动板，但他们上面都有ILI9341芯片，所以我们可以用相同的方法操作它。

2.如何操作它呢？

这是ILI9341驱动板的背面，我在上面做了些标注，应该会方便理解些。我们只要控制这些针脚的通电与否（高电平与低电平），就能够获得操控这块屏幕的“完整权限”！那这些针脚的定义是什么呢？我们一个一个看：

左上角有五个最重要的针脚，分别是LCD_RST、LCD_CS、LCD_RS、LCD_WR和LCD_RD：（直接用文字写不能冒号对齐，没办法，开个代码框(￣▽￣)~*）

LCD_RST ： 即LCD Reset，用于在通电之后复位，初始化整个模块。

LCD_CS  ： 即LCD Chip Select，用于多个芯片之间的片选操作。由于这块驱动板只有一个可用的芯片，所以一般该针脚不通电。

LCD_RS  ： 又称D/CX信号线，用于切换写命令（Command）和写数据（Data），当对显示屏写命令（Command）时，应该让针脚不通电，当对显示屏写数据（Data）时，应该让针脚通电。

LCD_WR  ： 写使能。当LCD_WR不通电，并且LCD_RD通电时，数据传输方向为写入。

LCD_RD  ： 读使能。

左下角的针脚负责供电，不细讲。

右上角的LCD_D0到LCD_D7是数据脚，通过控制它的通电与否来传输8个比特，也就是8个0或1。这种方式可以传输一个最小值0，最大值255的数字，我们用它来传输所有命令和数据。

右下角的SD_SS,SD_DI,SD_D0,SD_SCK适用于控制SD卡读写的，不属于ILI9341的范畴，我们先不讨论。

那么，如何操作它呢？这张图能够很清楚的说明：（下面用拉低代表示不通电，拉高表示通电，这样术语会更加标准）

 

  • 单片机开机，ILI9341驱动板接收到电流，开始进入待命状态
  • 拉低LCD_CS片选信号，选择对ILI9341芯片发送命令
  • 通过拉高拉低LCD_D0到LCD_D7数据脚，来表示二进制数据
  • 拉低拉高LCD_RS针脚来告诉机器这是一个命令，还是一个数据
  • 拉低LCD_WR，进行写使能（可以理解为按下回车键，把LCD_D0到D7的数据发送出去）

这就是发送一个命令或者数据的方法。二进制，十进制和十六进制的转换和表达先直接略过，如果要展开，那可能可以出一本书了( • ̀ω•́ )✧，关于LCD_D0到D7脚应该发送什么，ILITEK在设计ILI9341时就已经规定好了，中文文档在此：

接下来，就是，愉快的，编码时间啦( • ̀ω•́ )✧！！！

3.兼容性设定

不知刚才你有没有注意到数据脚是从LCD_D2开始的？那是因为Arduino Uno开发板的第0和1脚是USB针脚，不能被使用，只能从第2个针脚开始设计：

那我们在编程时要用到LCD_D0和LCD_D1时，就必须写成8和9。另外不同机器脚位也不一样，所以我用宏定义来简化程序：

#define LCD_D0   8
#define LCD_D1   9
#define LCD_D2   2
#define LCD_D3   3
#define LCD_D4   4
#define LCD_D5   5
#define LCD_D6   6
#define LCD_D7   7
#define LCD_RD   A0
#define LCD_WR   A1
#define LCD_RS   A2
#define LCD_CS   A3
#define LCD_RST  A4

这样即解决了LCD_D0和LCD_D1脚的问题，还搞定的不同开发板的兼容性问题。由于#define是在预编译阶段生成的，所以不会影响代码运行的速度。

4.发送命令和数据

调用这块屏幕的方法很明确，就是写入2进制数字。通过设计厂商提供的命令表发送相应的2进制命令和数据，实现操控。这样做的好处是无论你使用的是什么机器，什么驱动板，只要实现了LcdWriteCommand()和LcdWriteData()两个函数，就可以实现对屏幕的完全控制。

你当然可以用最直接的办法去控制引脚，比如digitalWrite():

void LcdWriteCommand(unsigned char d){
  //Write Command Mode On
  digitalWrite(LCD_RS,LOW);
  //Write Datas to LCD_D0 to LCD_D7
  digitalWrite(LCD_D0,d%2);
  d = d >> 1;
  digitalWrite(LCD_D1,d%2);
  d = d >> 1;
  digitalWrite(LCD_D2,d%2);
  d = d >> 1;
  digitalWrite(LCD_D3,d%2);
  d = d >> 1;
  digitalWrite(LCD_D4,d%2);
  d = d >> 1;
  digitalWrite(LCD_D5,d%2);
  d = d >> 1;
  digitalWrite(LCD_D6,d%2);
  d = d >> 1;
  digitalWrite(LCD_D7,d%2);
  d = d >> 1;
  //Enable Datas
  digitalWrite(LCD_WR,LOW);
  digitalWrite(LCD_WR,HIGH);
}

void LcdWriteData(unsigned char d){
  //Write Data Mode On
  digitalWrite(LCD_RS,HIGH);
  //Write Datas to LCD_D0 to LCD_D7
  digitalWrite(LCD_D0,d%2);
  d = d >> 1;
  digitalWrite(LCD_D1,d%2);
  d = d >> 1;
  digitalWrite(LCD_D2,d%2);
  d = d >> 1;
  digitalWrite(LCD_D3,d%2);
  d = d >> 1;
  digitalWrite(LCD_D4,d%2);
  d = d >> 1;
  digitalWrite(LCD_D5,d%2);
  d = d >> 1;
  digitalWrite(LCD_D6,d%2);
  d = d >> 1;
  digitalWrite(LCD_D7,d%2);
  d = d >> 1;
  //Enable Datas
  digitalWrite(LCD_WR,LOW);
  digitalWrite(LCD_WR,HIGH);
}

但是这样做的话，速度嘛。。。看看这个，你就不会想用digitalWrite了：

 

 单片机中，速度为王，我们还是直接改Register吧：

void LcdWriteCommand(unsigned char d){
  //Write Command Mode On
  fastDigitalWriteLOW(LCD_RS);
  //Write Datas to LCD_D0 to LCD_D7
  PORTD = (PORTD & B00000011) | ((d) & B11111100); 
  PORTB = (PORTB & B11111100) | ((d) & B00000011); 
  //Enable Datas
  fastDigitalWriteLOW(LCD_WR);
  fastDigitalWriteHIGH(LCD_WR);
}

void LcdWriteData(unsigned char d){
  //Write Command Mode On
  fastDigitalWriteHIGH(LCD_RS);
  //Write Datas to LCD_D0 to LCD_D7
  PORTD = (PORTD & B00000011) | ((d) & B11111100);
  PORTB = (PORTB & B11111100) | ((d) & B00000011);
  //Enable Datas
  fastDigitalWriteLOW(LCD_WR);
  fastDigitalWriteHIGH(LCD_WR);
}

这段代码中，我用了宏定义来实现fastDigitalWriteHIGH()和fastDigitalWriteLOW()，这两个定义能避免函数的栈调用。其实用内联函数来写也可以实现：

inline void fastDigitalWriteHIGH(int Pin){
  *(portOutputRegister(digitalPinToPort(Pin)))|=digitalPinToBitMask(Pin);
  return;
}

但我就是喜欢宏定义，而且宏定义行数少些。

另外你可能会疑惑：什么是PORTB和PORTD？

PORTB其实就是针脚8-13，PORTD其实就是针脚0-7：

 

 

 假如你有一个这样的二进制数：

00000100

把他转换成十进制：

4

再把它赋值给PORTD

PORTD = 4;

你就会发现针脚2通电了（图中连接到左边第一个红色灯泡）：

 

 

 这就是PORTD的真正意义，它使用一个从0到255的数，记录针脚0到7的通电情况。

那我们为什么不用digitalWrite()，而是要用PORTB和PORTD呢？因为快啊(￣▽￣)~*

5.Enjoy!

我们刚刚实现了LcdWriteCommand()和LcdWriteData()两个函数，现在，我们就可以实现对屏幕的完全控制了！

首先，先运行一段初始化命令：

  //Initialize Data Pins
  pinMode(LCD_D0,OUTPUT);
  pinMode(LCD_D1,OUTPUT);
  pinMode(LCD_D2,OUTPUT);
  pinMode(LCD_D3,OUTPUT);
  pinMode(LCD_D4,OUTPUT);
  pinMode(LCD_D5,OUTPUT);
  pinMode(LCD_D6,OUTPUT);
  pinMode(LCD_D7,OUTPUT);

  //Initialize Command Pins
  pinMode(LCD_RD,OUTPUT);
  pinMode(LCD_WR,OUTPUT);
  pinMode(LCD_RS,OUTPUT);
  pinMode(LCD_CS,OUTPUT);
  pinMode(LCD_RST,OUTPUT);
  digitalWrite(LCD_CS,LOW);
  digitalWrite(LCD_RD,HIGH);
  digitalWrite(LCD_WR,LOW);

  //Reset
  digitalWrite(LCD_RST,HIGH);
  delay(5);
  digitalWrite(LCD_RST,LOW);
  delay(15);
  digitalWrite(LCD_RST,HIGH);
  delay(15);

  LcdWriteCommand(0xCB);
  LcdWriteData(0x39);
  LcdWriteData(0x2C);
  LcdWriteData(0x00);
  LcdWriteData(0x34);
  LcdWriteData(0x02);

  LcdWriteCommand(0xCF);
  LcdWriteData(0x00);
  LcdWriteData(0XC1);
  LcdWriteData(0X30);

  LcdWriteCommand(0xE8);
  LcdWriteData(0x85);
  LcdWriteData(0x00);
  LcdWriteData(0x78);

  LcdWriteCommand(0xEA);
  LcdWriteData(0x00);
  LcdWriteData(0x00);
 
  LcdWriteCommand(0xED);
  LcdWriteData(0x64);
  LcdWriteData(0x03);
  LcdWriteData(0X12);
  LcdWriteData(0X81);

  LcdWriteCommand(0xF7);
  LcdWriteData(0x20);
  
  LcdWriteCommand(0xC0);    //Power control 
  LcdWriteData(0x23);   //VRH[5:0] 
 
  LcdWriteCommand(0xC1);    //Power control 
  LcdWriteData(0x10);   //SAP[2:0];BT[3:0] 

  LcdWriteCommand(0xC5);    //VCM control 
  LcdWriteData(0x3e);   //Contrast
  LcdWriteData(0x28); 
 
  LcdWriteCommand(0xC7);    //VCM control2 
  LcdWriteData(0x86);   //--
 
  LcdWriteCommand(0x36);    // Memory Access Control 
  LcdWriteData(0x48);   

  LcdWriteCommand(0x3A);
  LcdWriteData(0x55);

  LcdWriteCommand(0xB1);
  LcdWriteData(0x00);
  LcdWriteData(0x18);
 
  LcdWriteCommand(0xB6);    // Display Function Control 
  LcdWriteData(0x08);
  LcdWriteData(0x82);
  LcdWriteData(0x27);

  LcdWriteCommand(0x11);    //Exit Sleep 
  delay(120);
        
  LcdWriteCommand(0x29);    //Display on 
  LcdWriteCommand(0x2c);

这么多！不要怕，原样复制过去运行就好。这段命令是按照ILITEK设计文档中的规则发送的，用于初始化屏幕。运行完这段命令之后，我们就可以开始发自己的命令了。

我们试着来清一下屏。清屏就是指定一块区域，然后给屏幕每一个像素点的颜色为白色，这样就好了。

首先定义我们要写入的区域，这里就是从(0,0)写入到(239,319)：

int x1 = 0;
int x2 = 239;
int y1 = 0;
int y2 = 319;

接着通知屏幕我们要写入的区域的X坐标的起始、终止位置（命令0x2a）：

LcdWriteCommand(0x2a);

然后发送X坐标的起始位置（x1），和X坐标的终止位置（x2）。我们的机器一次只能发送八位数字，但八位数字最大只能表示255，所以我们要分两次发送，先发送前八位，再发送后八位：

LcdWriteData(x1>>8);
LcdWriteData(x1);
LcdWriteData(x2>>8);
LcdWriteData(x2);

Y坐标也是一样，只是把通知命令改成0x2b：

LcdWriteCommand(0x2b);
LcdWriteData(y1>>8);
LcdWriteData(y1);
LcdWriteData(y2>>8);
LcdWriteData(y2);

接着，我们发送开始写入的命令（0x2c），告诉屏幕我要开始发送像素了：

LcdWriteCommand(0x2c);

最后，发送所有像素的颜色数据（Data）。里面的RGB()宏定义是我在上一篇文章实现的。另外，因为是数据，所以我们要使用LcdWriteData()：

#define RGB(r,g,b) ((b&31)+((g&63)<<5)+((r&31)<<11))

for(int i=y1;i<=y2;i++){
  for(int j=x1;j<=x2;j++){
    LcdWriteData(RGB(31,63,31)>>8);
    LcdWriteData(RGB(31,63,31));
  }
}

保存，下载。

刷屏完整代码：

// Breakout/Arduino UNO pin usage:
// LCD Data Bit :   7   6   5   4   3   2   1   0
// Uno dig. pin :   7   6   5   4   3   2   9   8
// Uno port/pin : PD7 PD6 PD5 PD4 PD3 PD2 PB1 PB0
// Mega dig. pin:  29  28  27  26  25  24  23  22
#define LCD_D0   8
#define LCD_D1   9
#define LCD_D2   2
#define LCD_D3   3
#define LCD_D4   4
#define LCD_D5   5
#define LCD_D6   6
#define LCD_D7   7
#define LCD_RD   A0
#define LCD_WR   A1
#define LCD_RS   A2
#define LCD_CS   A3
#define LCD_RST  A4
#define fastDigitalWriteHIGH(Pin) *(portOutputRegister(digitalPinToPort(Pin)))|=digitalPinToBitMask(Pin)  //Faster digitalWrite(Pin,HIGH);
#define fastDigitalWriteLOW(Pin) *(portOutputRegister(digitalPinToPort(Pin)))&=~digitalPinToBitMask(Pin)  //Faster digitalWrite(Pin,LOW);
#define RGB(r,g,b) ((b&31)+((g&63)<<5)+((r&31)<<11))

void LcdWriteCommand(unsigned char d){
  //Write Command Mode On
  fastDigitalWriteLOW(LCD_RS);
  //Write Datas to LCD_D0 to LCD_D7
  PORTD = (PORTD & B00000011) | ((d) & B11111100); 
  PORTB = (PORTB & B11111100) | ((d) & B00000011); 
  //Enable Datas
  fastDigitalWriteLOW(LCD_WR);
  fastDigitalWriteHIGH(LCD_WR);
}

void LcdWriteData(unsigned char d){
  //Write Command Mode On
  fastDigitalWriteHIGH(LCD_RS);
  //Write Datas to LCD_D0 to LCD_D7
  PORTD = (PORTD & B00000011) | ((d) & B11111100);
  PORTB = (PORTB & B11111100) | ((d) & B00000011);
  //Enable Datas
  fastDigitalWriteLOW(LCD_WR);
  fastDigitalWriteHIGH(LCD_WR);
}

void setup(){
  //Initialize Data Pins
  pinMode(LCD_D0,OUTPUT);
  pinMode(LCD_D1,OUTPUT);
  pinMode(LCD_D2,OUTPUT);
  pinMode(LCD_D3,OUTPUT);
  pinMode(LCD_D4,OUTPUT);
  pinMode(LCD_D5,OUTPUT);
  pinMode(LCD_D6,OUTPUT);
  pinMode(LCD_D7,OUTPUT);

  //Initialize Command Pins
  pinMode(LCD_RD,OUTPUT);
  pinMode(LCD_WR,OUTPUT);
  pinMode(LCD_RS,OUTPUT);
  pinMode(LCD_CS,OUTPUT);
  pinMode(LCD_RST,OUTPUT);
  digitalWrite(LCD_CS,LOW);
  digitalWrite(LCD_RD,HIGH);
  digitalWrite(LCD_WR,LOW);

  //Reset
  digitalWrite(LCD_RST,HIGH);
  delay(5);
  digitalWrite(LCD_RST,LOW);
  delay(15);
  digitalWrite(LCD_RST,HIGH);
  delay(15);

  LcdWriteCommand(0xCB);
  LcdWriteData(0x39);
  LcdWriteData(0x2C);
  LcdWriteData(0x00);
  LcdWriteData(0x34);
  LcdWriteData(0x02);

  LcdWriteCommand(0xCF);
  LcdWriteData(0x00);
  LcdWriteData(0XC1);
  LcdWriteData(0X30);

  LcdWriteCommand(0xE8);
  LcdWriteData(0x85);
  LcdWriteData(0x00);
  LcdWriteData(0x78);

  LcdWriteCommand(0xEA);
  LcdWriteData(0x00);
  LcdWriteData(0x00);
 
  LcdWriteCommand(0xED);
  LcdWriteData(0x64);
  LcdWriteData(0x03);
  LcdWriteData(0X12);
  LcdWriteData(0X81);

  LcdWriteCommand(0xF7);
  LcdWriteData(0x20);
  
  LcdWriteCommand(0xC0);    //Power control 
  LcdWriteData(0x23);   //VRH[5:0] 
 
  LcdWriteCommand(0xC1);    //Power control 
  LcdWriteData(0x10);   //SAP[2:0];BT[3:0] 

  LcdWriteCommand(0xC5);    //VCM control 
  LcdWriteData(0x3e);   //Contrast
  LcdWriteData(0x28); 
 
  LcdWriteCommand(0xC7);    //VCM control2 
  LcdWriteData(0x86);   //--
 
  LcdWriteCommand(0x36);    // Memory Access Control 
  LcdWriteData(0x48);   

  LcdWriteCommand(0x3A);
  LcdWriteData(0x55);

  LcdWriteCommand(0xB1);
  LcdWriteData(0x00);
  LcdWriteData(0x18);
 
  LcdWriteCommand(0xB6);    // Display Function Control 
  LcdWriteData(0x08);
  LcdWriteData(0x82);
  LcdWriteData(0x27);

  LcdWriteCommand(0x11);    //Exit Sleep 
  delay(120);
        
  LcdWriteCommand(0x29);    //Display on 
  LcdWriteCommand(0x2c);

  //Set Writing Area
  int x1 = 0;
  int x2 = 239;
  int y1 = 0;
  int y2 = 319;
  LcdWriteCommand(0x2a);
  LcdWriteData(x1>>8);
  LcdWriteData(x1);
  LcdWriteData(x2>>8);
  LcdWriteData(x2);
  LcdWriteCommand(0x2b);
  LcdWriteData(y1>>8);
  LcdWriteData(y1);
  LcdWriteData(y2>>8);
  LcdWriteData(y2);

  //Start Writing
  LcdWriteCommand(0x2c);
  for(int i=y1;i<=y2;i++){
    for(int j=x1;j<=x2;j++){
      LcdWriteData(RGB(31,63,31)>>8);
      LcdWriteData(RGB(31,63,31));
    }
  }
}

void loop(){
  
}

接下来的路线就很简单了，把指定区域的命令（0x2a,0x2b,0x2c）分装成LcdOpenWindow()函数，再实现LcdFill()函数，一个完整的ILI9341驱动就完成了：

#define LCD_D0   8
#define LCD_D1   9
#define LCD_D2   2
#define LCD_D3   3
#define LCD_D4   4
#define LCD_D5   5
#define LCD_D6   6
#define LCD_D7   7
#define LCD_RD   A0
#define LCD_WR   A1
#define LCD_RS   A2
#define LCD_CS   A3
#define LCD_RST  A4
#define fastDigitalWriteHIGH(Pin) *(portOutputRegister(digitalPinToPort(Pin)))|=digitalPinToBitMask(Pin)  //Faster digitalWrite(Pin,HIGH);
#define fastDigitalWriteLOW(Pin) *(portOutputRegister(digitalPinToPort(Pin)))&=~digitalPinToBitMask(Pin)  //Faster digitalWrite(Pin,LOW);
#define RGB(r,g,b) ((b&31)+((g&63)<<5)+((r&31)<<11))

void LcdWriteCommand(unsigned char d){
  //Write Command Mode On
  fastDigitalWriteLOW(LCD_RS);
  //Write Datas to LCD_D0 to LCD_D7
  PORTD = (PORTD & B00000011) | ((d) & B11111100); 
  PORTB = (PORTB & B11111100) | ((d) & B00000011); 
  //Enable Datas
  fastDigitalWriteLOW(LCD_WR);
  fastDigitalWriteHIGH(LCD_WR);
}

void LcdWriteData(unsigned char d){
  //Write Command Mode On
  fastDigitalWriteHIGH(LCD_RS);
  //Write Datas to LCD_D0 to LCD_D7
  PORTD = (PORTD & B00000011) | ((d) & B11111100);
  PORTB = (PORTB & B11111100) | ((d) & B00000011);
  //Enable Datas
  fastDigitalWriteLOW(LCD_WR);
  fastDigitalWriteHIGH(LCD_WR);
}

void LcdInit(void){
  //Initialize Data Pins
  pinMode(LCD_D0,OUTPUT);
  pinMode(LCD_D1,OUTPUT);
  pinMode(LCD_D2,OUTPUT);
  pinMode(LCD_D3,OUTPUT);
  pinMode(LCD_D4,OUTPUT);
  pinMode(LCD_D5,OUTPUT);
  pinMode(LCD_D6,OUTPUT);
  pinMode(LCD_D7,OUTPUT);

  //Initialize Command Pins
  pinMode(LCD_RD,OUTPUT);
  pinMode(LCD_WR,OUTPUT);
  pinMode(LCD_RS,OUTPUT);
  pinMode(LCD_CS,OUTPUT);
  pinMode(LCD_RST,OUTPUT);
  digitalWrite(LCD_CS,LOW);
  digitalWrite(LCD_RD,HIGH);
  digitalWrite(LCD_WR,LOW);

  //Reset
  digitalWrite(LCD_RST,HIGH);
  delay(5);
  digitalWrite(LCD_RST,LOW);
  delay(15);
  digitalWrite(LCD_RST,HIGH);
  delay(15);

  LcdWriteCommand(0xCB);
  LcdWriteData(0x39);
  LcdWriteData(0x2C);
  LcdWriteData(0x00);
  LcdWriteData(0x34);
  LcdWriteData(0x02);

  LcdWriteCommand(0xCF);
  LcdWriteData(0x00);
  LcdWriteData(0XC1);
  LcdWriteData(0X30);

  LcdWriteCommand(0xE8);
  LcdWriteData(0x85);
  LcdWriteData(0x00);
  LcdWriteData(0x78);

  LcdWriteCommand(0xEA);
  LcdWriteData(0x00);
  LcdWriteData(0x00);
 
  LcdWriteCommand(0xED);
  LcdWriteData(0x64);
  LcdWriteData(0x03);
  LcdWriteData(0X12);
  LcdWriteData(0X81);

  LcdWriteCommand(0xF7);
  LcdWriteData(0x20);
  
  LcdWriteCommand(0xC0);    //Power control 
  LcdWriteData(0x23);   //VRH[5:0] 
 
  LcdWriteCommand(0xC1);    //Power control 
  LcdWriteData(0x10);   //SAP[2:0];BT[3:0] 

  LcdWriteCommand(0xC5);    //VCM control 
  LcdWriteData(0x3e);   //Contrast
  LcdWriteData(0x28); 
 
  LcdWriteCommand(0xC7);    //VCM control2 
  LcdWriteData(0x86);   //--
 
  LcdWriteCommand(0x36);    // Memory Access Control 
  LcdWriteData(0x48);   

  LcdWriteCommand(0x3A);
  LcdWriteData(0x55);

  LcdWriteCommand(0xB1);
  LcdWriteData(0x00);
  LcdWriteData(0x18);
 
  LcdWriteCommand(0xB6);    // Display Function Control 
  LcdWriteData(0x08);
  LcdWriteData(0x82);
  LcdWriteData(0x27);

  LcdWriteCommand(0x11);    //Exit Sleep 
  delay(120);
        
  LcdWriteCommand(0x29);    //Display on 
  LcdWriteCommand(0x2c);
}

void LcdOpenWindow(unsigned int x1,unsigned int y1,unsigned int x2,unsigned int y2){
  LcdWriteCommand(0x2a);
  LcdWriteData(x1>>8);
  LcdWriteData(x1);
  LcdWriteData(x2>>8);
  LcdWriteData(x2);
  LcdWriteCommand(0x2b);
  LcdWriteData(y1>>8);
  LcdWriteData(y1);
  LcdWriteData(y2>>8);
  LcdWriteData(y2);
  LcdWriteCommand(0x2c);
}

void LcdFill(int x,int y,int width,int height,unsigned int color)
{
  LcdOpenWindow(x,y,x+width-1,y+height-1);
  for(int i=y;i<y+height;i++){
    for(int j=x;j<x+width;j++){
      LcdWriteData(color>>8);
      LcdWriteData(color);
    }
  }
}

void setup(){
  LcdInit();
  LcdFill(0,0,239,319,RGB(31,63,31));
  LcdFill(10,10,100,100,RGB(31,0,0));
  LcdFill(20,20,110,110,RGB(0,63,0));
  LcdFill(30,30,120,120,RGB(0,0,31));
}

void loop(){
  
}

 

 都看到这了，还不点个赞吗？(✪ω✪)

加载全部内容
相关教程
猜你喜欢
用户评论